Nitek VR148UTP Manuel d'utilisateur télécharger pdf

Model VR148UTP

Network Extender with PoE

Installation and

Operation Manual

Introduction

The VR148UTP Network Extender is designed to greatly extend the distances to which IP cameras and other network

devices can operate. The VR148UTP Network Extender consists of two units, a transmitter and a receiver. Only the

transmitter provides PoE to the connected network device. The receiver is installed at the NVR/IP equipment side and

the transmitter at the IP camera side of the installation.

Note: A sticker on the bottom of each unit identifies whether it is the transmitter or the receiver.

NITEK ®

De Schans 19-21 2a

8231 KA Lelystad

Tel: +31(0)320-2300005

Fax: +31(0)320-282186

E-mail: [email protected]

WWW.NITEK.NL

USA

5410 Newport Drive, # 24

Rolling Meadows, IL 60008

Phone: (847) 259-8900

Fax: (847) 259-1300

E-mail: [email protected]

WWW.NITEK.NET

EUROPE

072310 681200105

POWER

10/100

Data

Status

ETHERNET

WIRE PAIR

LINK

Type

Speed Off 10 Mbs

LED Green 100 Mbs

Activity Off No Network

LED On Network Detected

Blinking Network Activity

eed Off 10 Mbs

LED

reen 100 Mbs

Activit

ff No Networ

n Network Detected

Blinkin

Network Activity

Status Blinking Establishing Link

LED On Link Established

Type On Transmitter

LED Off Receiver

FRONT

BACK

Ground

Connection

NITEK

POWER INPUT

12-24 AC/DC, 0-100 Hz

Class 2 only, 1 Amp max.

COMMERCIAL

CCTV PRODUCT

40FE

E325724

24 AC

VR148UTP Network Extender Installation Drawing

Install Network to VR148UTP and IP Cameras

Refer to the above diagram when installing. Use best industry practices and follow all local building codes.

1) Connect an earth ground to each unit before making any additional connections.

2) Connect a network cable from the security room or IP network equipment to the receiver.

3) Connect a twisted pair cable between the transmitter and the receiver. Use center terminals of the RJ11connector.

4) Connect a network cable from the transmitter’s Ethernet jack to the IP camera or other network device.

5) Connect a Class 2 power transformer to the push in power connector of each VR148UTP unit. The units

require 24VAC @ 1 Amp. There is no polarity to these terminals.

Normal Operation

When power is applied to both units the Network LED’s will come on and the link status LED will blink for about 30

seconds as the link is being optimized. When the link is stable the link status LED will remain “ON”. The data LED will

blink with network activity.

The separate protective earthing terminal provided on this product shall be permanently connected to earth.

1 mile (1,600 m)

24AWG or Better

Twisted Pair

VR148UTP

Receiver

VR148UTP

Transmitter

w/PoE

1 2

NITEK ® 1
Troubleshooting 2

Résumé du contenu

Page 1 - NITEK ®

Model VR148UTP Network Extender with PoE Installation and Operation Manual Introduction The VR148UTP Network Extender is designed to greatly extend t

Page 2 - Troubleshooting

Troubleshooting After completing installation, if the units are not operating properly, check each step at each unit in order. 1) If the Power LED

Commentaires sur ces manuels

Pas de commentaire

Nitek VR148UTP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Nitek VR148UTP. Nitek VR148UTP User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Nitek VR148UTP